Skip to content
GOLDENRefractories Pvt. Ltd.
Silica ramming mass · Urla, Raipur

We hold back 1,700 °C

Golden Refractories makes the dry quartz lining that stands between liquid steel and the copper coil of an induction furnace. It is the thinnest, hottest wall in the melt shop.

01 — What is ramming mass?

The wall inside the furnace.

  1. The coilAn induction furnace melts steel with a water-cooled copper coil. The coil must never meet the metal.
  2. The mass goes inDry silica ramming mass is poured into the gap between the coil and a steel former, layer by layer.
  3. Rammed tightEach layer is rammed or vibrated until the grains lock together. No water, no mortar. Just graded quartz.
  4. First heatThe former melts away with the first charge. Liquid steel now sits against the quartz wall.
  5. Three zonesHeat sinters the hot face into glassy armour. Behind it sits a fritted layer, then loose powder that cushions the coil and stops cracks running through.
02 — From quartz to crucible

Eight steps from rock to rammable.

01
Select the stone

It starts with high-purity white quartz and quartzite. The purer the silica, the higher the heat it can stand.

03 — The grain recipe

Big grains for strength. Small ones to fill the gaps.

A lining is only as dense as its packing. Coarse grains form the skeleton, medium grains sit between them, and fines fill what is left. Fewer voids means less room for metal and slag to get in.

4 – 5 mm≤3%
3 – 4 mm~8%
2 – 3 mm~17%
1 – 2 mm~12%
0.2 – 1 mm~27%
< 0.2 mmrest

A typical industry grading, shown for illustration. Golden blends to the furnace size; ask for the grading sheet of your grade.

CoarseMediumFines
04 — The range

Three ways to line a furnace.

Choose by binder and by how you want it supplied. Processed quartz sits on its own shelf below, ground and sized to order.

Flagship
Close-up drawing of boron oxide-based silica ramming mass

Boron Oxide-Based Silica Ramming Mass

Boron oxide goes in as the binder directly, so the binding phase is present from the start instead of being formed from boric acid in the furnace.

Binder
Boron oxide (B₂O₃)
Supplied
Ready to ram
Best for
Induction furnace linings
Enquire ↗
Ready to ram
Close-up drawing of premix silica ramming mass

Premix Silica Ramming Mass

Boric acid binder mixed in at our plant. Open the bag and ram the lining.

Binder
Boric acid
Supplied
Premixed at our plant
Best for
Induction furnace linings
Enquire ↗
Your binder
Close-up drawing of non-premix silica ramming mass

Non-Premix Silica Ramming Mass

Graded silica without binder, for melt shops that add their own at site.

Binder
None, added at site
Supplied
Graded silica only
Best for
Shops with their own binder practice
Enquire ↗
Close-up drawing of nali top material

Nali Top Material

Silica-based material for the spout (nali) and top of the furnace.

Enquire ↗

Processed quartz.

Ground and sized to order. Marker shows where each sits from coarse to fine.

Close-up drawing of quartz grains

Quartz Grains

Sized quartz grains across a range of mesh sizes.

CoarseFine
Enquire ↗
Close-up drawing of quartz fines

Quartz Fines

Fine quartz for industrial use.

CoarseFine
Enquire ↗
Close-up drawing of quartz powder

Quartz Powder

Processed quartz ground to the mesh size you specify.

CoarseFine
Enquire ↗
05 — Our specialty

Why boron oxide?

The usual way

Boric acid H₃BO₃

Boric acid has to break down in the heat, giving off water, before it becomes the boron oxide that does the binding.

The Golden way

Boron oxide B₂O₃

We put boron oxide in directly. The active binding phase is already there, with no water to drive off during preheating.

Glass that seals the gaps.

As the lining heats up, boron oxide reacts with the silica grains and forms a borosilicate glass. It flows into the pores between grains and locks them into one dense wall.

  • 01Denser, stronger sintered lining
  • 02Better resistance to erosion and slag attack
  • 03Less risk of cracking during preheating
  • 04Potential for a longer lining campaign

Potential benefits from our technical note. Results depend on furnace, practice and charge.

300 °C
0°CLiquid steel a silica lining is built to hold back
>99%SiO₂ in our premium grade*
0Binder options: boron oxide or boric acid premix
0Products, from lining mass to quartz fines

*Grade-dependent. Test certificate available on request.

06 — Where we are

Made in Urla, Raipur.

Raipur sits at the centre of one of India's busiest steel belts. Our unit in Urla Industrial Area is close to the melt shops and foundries we supply, so material reaches the furnace quickly and our team is a phone call away.

  • Steel melt shops
  • Induction furnace operators
  • Iron foundries
  • Mild steel & cast iron melting
  • Industrial quartz buyers
Managing DirectorsVikash AgarwalSoham Agarwal
Talk to us

Reliningsoon?

Tell us your furnace size and the grade you use today. We'll come back with the right material and a price.